Skip to main content

Modify place jurisdictions

This windows lets you modify the standard place jurisdictions format of any Gedcom file and also align all places names existing throughout the Gedcom file to this definition.

This definition is saved in the header of the Gedcom file. It is therefore specific to each genealogy file and there is only one for each file.

EachIf placeyou name that is requesteddecide to align all place names to the formatstandard definitionformat, each place name will be modified accordingly and saved in the Gedcom file.

Description

en_file-places-1.png

This panel shows the existing format at the top under "Current format". Where does this current format come from?

  • When you first create a genealogy file, Ancestris uses the main language to define the place jurisdictions format.
  • When you migrate a Gedcom file from another software, Ancestris will also define the place format if none already exists, unless you do not convert the file when migrating it from this other software. In this case, Ancestris leaves the Gedcom file untouched, and just opens it. The Current format can potentially be empty if the previous software did not use this feature of the Gedcom standard.

Under "Current format" is an indication of how many different locations are found in the Gedcom file, and how many of them are not aligned to the place jurisdiction format. A button appears on the right hand side to let you decide to convert them.

The new format is at the bottom under "New jurisdictions format". If it is different from the current format, a button will appear to let you convert from the current to the new format, by defining the mapping table of the jurisdictions. See below.

The middle part of the panel is to create a new format using the buttons

Here is how to proceed to define or change a place format.

First define the new jurisdictions format

  • We use the Add criteria button Propriétés_lieux_créer.png to enter each of the jurisdictions one by one in the field to the right of this button.
  • We use the Remove criteria button Propriétés_lieux_supprimer.png on each of the jurisdictions to be removed.
  • We then use the movement buttons Propriétés_lieux_déplacer.png to order the new jurisdictions from the smallest to largest geographic area.

By the way, the Empty button  Propriétés_lieux_vide.png allows you to insert an empty jurisdiction, and the reset button Propriétés_lieux_réinitialiser.png starts all over again.

The picture below shows an example when changing from the US to the French place format.

en_file-properties-4-change.pngen_file-places-2.png

We then provide the conversion map

We checkmake sure the convert box box en_file-properties-4-convert.png thenis checked wnd we click on the Conversion button Propriétés_lieux_convertir.png which. displaysThis will display a correspondence mapping table between the startingcurrent and endingnew formats.

The screen explains what to do.

HereIt is theshown screenshotbelow after dragging and dropping the first 4 American criteria which correspond to four of the French criteria.

TheIf locationa criterionnew didjurisdiction does not exist in the previouscurrent format, so it will be empty in the new format.location.

TheIf Countya criterioncurrent isjurisdiction does not yetexist assigned to a French criterion. If you allocate it toin the department,new format, the Countycorresponding information will be kept. if you leave County unassigned ", theplace information will disappear onafter conversion.

en_file-properties-4-settings.pngen_file-places-3.png

Once this correspondencecorrespondance is established, close the window and click on the Next button.OK.

If you hadhave changed the format of the places without checking the conversion box, two cases would arise:

  • either the number of criteria between the old and the new formats is different: in this case, Ancestris would notify you of an anomaly in all places when checking for anomalies. If you reduce the number of criteria, you will obviously loose the data corresponding to the criteria which have no position in the new format.

en_file-properties-4-convert-warning.png

  • or the number of criteria is the same: in this case, you have made a name change of the criteria and all data will be converted without loosing any.

     

    Result

    By clicking Finish on the previous screen, Ancestris asks you for each confirmation one by one.

     

    Confirmation is also requested if locations or the Gedcom norm are to be modified.

    If you confirm, the transformations take place.

    In case of simple modification, the following window appears and everything went well.

    en_file-properties-success.png

    In the event of a larger transformation, the result window lists all the changes that have taken place.

    In another example created to illustrate, here's what a result with errors would look like.

    en_file-properties-summary.png

    The interpretation would be as follows:

    • Simple properties have been changed without error.
    • The change of Gedcom norm produced one error, listed in the the dropdown list.
    • The change of location format converted 85 locations successfully.
    • The attachment of the 6 lost media went well.

    If you have any doubts and want to start over, you can always Cancel the operation completely by clicking the Undo button undo.png on the general Ancestris toolbar.

    If you want to analyze the anomalies, you can also go to Menu / Tools / Validate Gedcom compliance and data consistency.

    menu-gedcom-compliance.png